Although costs will vary, you can probably expect to spend anywhere between $350.00 - $1,000.00 dollars for an inspection of a single family home. And who pays for it? Well, since the benefit is almost entirely that of the buyer, it's usually the buyer who pays the cost of the home inspection …particularly in a "hot" real estate market, where the sellers have more leverage. All things considered, it's a small price to pay for the peace of mind it provides, and the negotiating power it can give you -- especially if it indicates that there are major repairs required, but you decide to make an offer anyway.

When it comes to making your offer to purchase, Mike Perrin can provide you with good advice on how to allow for a home inspection as a part of this process. Subject to the homeowner's permission, you can commission a Home Inspection before or even after submitting your offer to purchase. This is done by having Mike prepare a conditional offer that's contingent on a Home Inspection report that's acceptable to you. This approach gives you some distinct advantages: if the conditional offer is accepted, the property is temporarily held against other offers, yet you still have a legal escape route if the report turns up some major negative surprises, such as a bad roof or a crumbling foundation. On the other hand, if the conditional offer isn't accepted, then the need to pay for a home inspection may never arise. Mike can counsel you on the best approach to suit your market and your individual situation.

10 Tips You Need to Know to Pass Your Home Inspection

1. Defective Plumbing

Defective plumbing can manifest itself in two different ways: leaking, and clogging. A visual inspection can detect leaking, and an inspector will gauge water pressure by turning on all faucets in the highest bathroom and then flushing the toilet. If you hear the sound of running water, it indicates that the pipes are undersized. If the water appears dirty when first turned on at the faucet, this is a good indication that the pipes are rusting, which can result in severe water quality problems.

2. Damp or Wet Basement

An inspector will check your walls for a powdery white mineral deposit a few inches off the floor, and will look to see if you feel secure enough to store things right on your basement floor. A mildew odor is almost impossible to eliminate, and an inspector will certainly be conscious of it.

It could cost you $200-$1,000 to seal a crack in or around your basement foundation depending on severity and location. Adding a sump pump and pit could run you around $750 - $1,000, and complete waterproofing (of an average 3 bedroom home) could amount to $5,000-$15,000. You will have to weigh these figures into the calculation of what price you want to net on your home.

3. Inadequate Wiring & Electrical

Your home should have a minimum of 100 amps service, and this should be clearly marked. Wire should be copper or aluminum. Home inspectors will look at octopus plugs as indicative of inadequate circuits and a potential fire hazard.

4. Poor Heating & Cooling Systems

Insufficient insulation, and an inadequate or a poorly functioning heating system, are the most common causes of poor heating. While an adequately clean furnace, without rust on the heat exchanger, usually has life left in it, an inspector will be asking and checking to see if your furnace is over its typical life span of 15-25 yrs. For a forced air gas system, a heat exchanger will come under particular scrutiny since one that is cracked can emit deadly carbon monoxide into the home. These heat exchangers must be replaced if damaged - they cannot be repaired.

5. Roofing Problems

Water leakage through the roof can occur for a variety of reasons such as physical deterioration of the asphalt shingles (e.g. curling or splitting), or mechanical damage from a wind storm. When gutters leak and downspouts allow water to run down and through the exterior walls, this external problem becomes a major internal one.

6. Damp Attic Spaces

Aside from basement dampness, problems with ventilation, insulation and vapor barriers can cause water, moisture, mold and mildew to form in the attic. This can lead to premature wear of the roof, structure and building materials. The cost to fix this damage could easily run over $2,500.

7. Rotting Wood

This can occur in many places (door or window frames, trim, siding, decks and fences). The building inspector will sometimes probe the wood to see if this is present - especially when wood has been freshly painted.

8. Masonry Work

Re-bricking can be costly, but, left unattended, these repairs can cause problems with water and moisture penetration into the home which in turn could lead to a chimney being clogged by fallen bricks or even a chimney which falls onto the roof. It can be costly to rebuild a chimney or to have it repainted.

9. Unsafe or Over-fused Electrical Circuit

A fire hazard is created when more amperage is drawn on the circuit than was intended. 15 amp circuits are the most common in a typical home, with larger service for large appliances such as stoves and dryers. It can cost several hundred dollars to replace your fuse panel with a circuit panel.

10. Adequate Security Features

More than a purchased security system, an inspector will look for the basic safety features that will protect your home such as proper locks on windows and patio doors, dead bolts on the doors, smoke and even carbon monoxide detectors in every bedroom and on every level. Even though pricing will vary, these components will add to your costs. Before purchasing or installing, you should check with your local experts.

When you put your home on the market, you don’t want any unpleasant surprises that could cost you the sale of your home. By having an understanding of these 11 problem areas as you walk through your home, you’ll be arming yourself against future disappointment.